Skip to content

Learning To Ride A Motorbike

All those who are interested in learning to ride a motorcycle should always ensure they take all the safety measures first. Safety will begin with wearing the appropriate gears for the type of learning you want to embark on. Learners should also enroll in motorcycle safety courses that they will be given proper guidance and skills on how to safely and properly ride.

Learning to ride

The first and most important step in getting yourself enrolled in a motorcycle safety course. The course will provide one with correct tools for learning both safety rules to observe and techniques while riding. One might be provided with a motorbike to use while enrolled in a course and this is very advantageous for those who do not have a one of their own. After the end of a series of lessons, one will have acquired basics of operation and safety. This will enable you to apply for the appropriate license for your bike class.


One should always familiarize themselves with the basic controls on the motorcycle before they begin to ride. Riding will require quick thinking and without the basics knowledge of the controls, one might find themselves in dangerous situations while riding. Learn about controls like the hand clutch located on the left handlebar; this is used for disengaging the power when shifting gears. The gear shifter, located on the left foot is used for changing one gear down or up while re-pulling the clutch lever. The throttle, on the right handlebar, is used to accelerate the bike. On the right handlebar is the handbrake that is used to apply brakes on the front wheel.

Get on the bike

One should always get on the bike from the left side of the motorcycle. You get hold of the left handlebar; swing your right foot over the motorcycles seat. The left foot should be firmly standing on the ground while the right foot is stepping on the rear gears on the right of the bike. Before starting the bike, go through the functions on the bike to get to know where every one of them is located. Make sure you can reach the handlebar making sure your hands have a bend on the elbow, the clutch lever and the brake levers comfortable. Make sure also the switches on the handlebar are within reach by your fingers.


Turn your key to ignition, put your bike to neutral by downshifting to first gear and shift up once. Push the start button, and the engine will be on. The bike will warm up for like 30 seconds before the engine is ready. Pull the clutch lever back and the bike will pull itself forward. Therefore, to learn to ride a motorcycle repeat all the above many times.

Engine Options For A Personal Hovercraft

Small personal hovercraft are fast becoming the expensive preferred toy of the younger set with enough money to enjoy themselves. A world class hover craft manufacturer will charge between 10000 and 15000 USD for such an air cushioned vehicle, depending on the options chosen. Such options may include a choice of engines, color (obviously) and additional features such as extra storage space, harnesses or short wave radio. Engine choice is an important point to consider before you buy a hovercraft.

Two stroke engines are common. These tend to be noisier and run at higher revolutions than their four stroke cousins and the fuel used is different. A two stroke hovercraft engine uses a lower octane mixture of gas (petrol) mixed with 2% oil. Basically, this means that the engine parts are lubricated by the oil mixed in with the fuel. A disadvantage of this is that the fuel needs to be mixed yourself, or either bought ready to use, which is expensive. The big advantage is that a two stroke engine is generally cheaper pound for pound, but is also noisier, particularly when used for lift and forward thrust applied to an ACV.

A four stroke motor has an oil reservoir, or sump, which is kept to a certain level and a pump moves it around the engine to ensure that all moving parts don't wear too much. Actually, the moving parts of an engine should never touch - a film of oil always separates their surfaces. A four stroke engine may be air or water cooled, depending on the size of the craft and it's intended use. Such uses can include leisure, rescue and survey operations both on dry land and over water.

The best hovercraft manufacturers design an engine compartment as part of the hull construction. This keeps the engine a little quieter and it's also safer in the event that it malfunctions, for example. A robust lid gives good access for maintenance and this can be locked securely until access is required. With clever hovercraft design, such a compartment could be sunk a little into the hull material without compromising it's impact strength, thereby optimizing space for passengers and equipment.

Smaller vehicles tend to use just one motor and ducting is used to redirect air flow downwards for upwards thrust, and to the rear for forward propulsion. It's obvious that a two motor machine will have more power for lift and thrust, and this may be necessary for machines designed for a heavy payload, or regularly lifting off water. However, such an arrangement will inevitably mean more noise and ear protection is recommended for all the family.

The General Way To Replace Car Battery.

Have you been suffering the usual signs indicating your battery may be about to fail , you might have been experiencing some electrical trouble , slow starting or maybe its just getting near its average age lifespan which is generally 2-4 years.

If its too late and you find yourself stranded with a completely dead car battery, you might to consider finding a local mobile car battery replacement service in your area.

If your thinking about changing it yourself , this gives you a general idea of the steps you need to take . Double check the car manufacturers guide before actually attempting to do so.

Don't get caught out starting to change the car battery and find you have the wrong one or you don't have the correct tools to complete the job.

If your car has special requirements , and your not comfortable changing your battery, its best to appoint a car battery repair specialist.

General Battery Swap Out Procedure.

Step 1 Everything Must Be Switched Off

Ensure you have turned everything off and keys are removed from ignition.

Step 2 Where's the battery.

The most common places you will find the battery are under the hood, in the boot, or under the seats.

Step 3 Un-doing the battery clamps.

Car Batteries are normally held down with a clamp, which will either be placed across the top or at the base of the battery. You will need either need a spanner or socket to undo.

Step 4 Trying to Save Electrical Settings.

Your vehicle probably has electrical settings saved in its memory, these could possibly lost if you disconnect your battery without an external power back up. These can usually be purchased on line or at a auto shop for a reasonable cost.

Step 5 Time To Detach The Battery.

Make sure the area you are working in is clear and easy to access, if your using external power be careful as the battery leads will still be powered when detached.

Disconnecting the battery leads

(Disconnect The Negative Lead 1st).

Start by undoing and detaching the negative lead first , it will have the - (minus) sign on it or the show on the battery itself.

(Disconnect The Positive Lead Next).

Once you have the negative lead off , proceed to take off the positive terminal next which has the + (plus) sign on it .

After you have the leads removed shift them out of the way , so they do not come into contact with anything else and you can remove the old battery easily.

Step 6. Fitting The New Battery.

Before you lift the new battery into place , make sure the area is clear and battery leads are not in the way. Place the new battery into its location.

(Connect the Positive Terminal ).

Attach the positive lead onto the positive battery terminal first , make sure its pushed down and secure. Tighten the nut or bolt back up.

(Secure the Negative Terminal 2nd).

Next you want to attach the negative lead, make sure its secure and tightened. If you battery has a eternal vent pipe , connect it now.

Step 7 Remove Any External Power Connected.

Once you have the new car battery in place and hooked up, make sure if you have any external power connected you disconnect it before starting the vehicle.

Step 8. Start The Car And Test.

Once your happy , proceed to start the car and test everything is working.

Step 9. Secure The Battery Back Down.

Now you have started the vehicle and are confident that all is ok, refit the battery hold down ,make sure you do not make connection with the live battery terminals and the battery is secure.

Well done you should now have your new car battery fitted and everything working as it should.